This page contains a price list of all Sherline accessories that we sell.
Other price lists:
Contents
SHERLINE ACCESSORIES
| Part Number | Part | Weight | Cost |
|---|---|---|---|
| 1012 | SENSITIVE DRILLING ATTACHMENTThreads onto mill spindle. Spring loaded 5/32" chuck is pulled down by hand using a bearing supported knurled collar. Provides quick action and great "feel" when drilling small holes. | 0.91kg 2lbs | £138.80 |
| 1074 | STEADY RESTSupports the end of long work for center drilling | 0.34kg 0.75lbs | £50.40 |
| 1090 | FOLLOWER RESTSupports thin work, keeps it from deflecting away from the cutter, moves with the lathe saddle to "follow" the work | 0.34kg 0.75lbs | £88.20 |
| 1160 | WW COLLET SETP/N 1161 included in set. Collets are like small, individually sized chucks for holding a specific diameter tool or material. WW collets have a hole through the collet and drawbar to accept long material. Traditionally used by watch and clock makers. Sherline WW collets have a .312-.313 body size and .275-40 thread. | 0.23kg 0.5lbs | £113.50 |
| 116000 | WW COLLET BLANK, Large Head | 0.02kg 0.05lbs | £14.10 |
| 116000+size | WW COLLET, CUSTOM SIZECustom size collets can be ordered in sizes from .050" to .320" or 1.28 mm to 8.13 mm. For example, a custom collet might be ordered as 116000 .100" or 116000 2.75 mm.) Custom collets are not laser engraved with size information. Allow 3 weeks for delivery. | 0.02kg 0.05lbs | £50.40 |
| 1160001 | WW COLLET BLANK, Small Head | 0.02kg 0.05lbs | £14.10 |
| 116001 | 1/64″ WW COLLET | 0.02kg 0.05lbs | £50.40 |
| 116002 | 1/32″ WW COLLET | 0.02kg 0.05lbs | £40.70 |
| 116003 | 3/64″ WW COLLET | 0.02kg 0.05lbs | £26.90 |
| 116004 - 116020 | WW COLLETS from size 1/16″ to 5/16″ by 64ths.The part number is given as 1160__ plus the number of 64ths to denote size. For example, 13/64" is P/N 116013 and a 1/4" collet (16/64") is P/N 116016. | 0.02kg 0.05lbs | £21.70 |
| 1161 | WW COLLET ADAPTER & DRAWBARIncluded in collet set. Adapts WW taper to #1 Morse taper of Headstock | 0.23kg 0.5lbs | £63.20 |
| 1162 | DELUXE WW COLLET SET (Inch)17 collets, adapter, drawbar, pot chucks, knockout bar, etc. in wooden case | 1.36kg 3lbs | £346.60 |
| 1163 | 8.0 MM COLLET ADAPTER & DRAWBARWW collets vary somewhat depending on manufacturer. This adapter holds those with a .314-.315 body size | 0.23kg 0.5lbs | £69.40 |
| 1164 | WW COLLET FIXTUREAllows WW collets with .312-.313 body to be held on face of rotary table or mill table. | 0.45kg 1lbs | £132.50 |
| 1165 | 8.0 MM COLLET FIXTUREAllows WW collets with .314-.315 body to be held on face of rotary table or mill table. | 0.45kg 1lbs | £145.00 |
| 1170 | OAK WW COLLET STORAGE BOXA high quality storage box that holds up to 22 WW collets plus collet pot chucks, drawbar, knockout bar and WW collet adapter. Beveled corners, brass hardware, satin lacquer finish. | 0.45kg 1lbs | £37.90 |
| 1171 | OAK WW COLLET STORAGE BOXA high quality storage box that holds up to 96 WW collets. Beveled corners, brass hardware, oak insert with 96 holes, satin lacquer finish. | 0.45kg 1lbs | £44.10 |
| 117803 | .3 mm WW COLLET | 0.02kg 0.05lbs | £50.40 |
| 117804 | .4 mm WW COLLET | 0.02kg 0.05lbs | £50.40 |
| 117805 - 117808 | WW COLLETS from size .5mm through .8 mm by .1 mm increments.The Part number is given as 11780 plus the collet size in .1 mm. For example, a .6 mm collet would be P/N 117806 | 0.02kg 0.05lbs | £50.40 |
| 117809 - 117814 | WW COLLETS from size .9mm through 1.4 mm by .1 mm increments.The part number is given as 11780_ or 1178__ plus the collet size in .1 mm. For example, a 1.1 mm collet would be P/N 117811. | 0.02kg 0.05lbs | £40.70 |
| 117815 - 117880 | WW COLLETS from size 1.5 mm through 8.0 mm by .1 mm increments.The part number is given as 1178__ plus the collet size in .1 mm. For example, a 6.4 mm collet would be P/N 117864. | 0.02kg 0.05lbs | £21.70 |
| 1179 | DELUXE WW COLLET SET (Metric)14 collets, pot chucks, etc. in wooden case. P/N 1161 included in set | 1.36kg 3lbs | £308.80 |
| 1180 | COMPLETE METRIC WW COLLET SETThe set is contained in a P/N 1171 oak collet box with 96-hole oak insert. | 1.82kg 4lbs | £1178.20 |
| 1182 | BULLNOSE LIVE CENTERSupports tubing or stock with a large end hole when turning between centers. Dual preloaded bearings. | 0.34kg 0.75lbs | £101.30 |
| 1185 | VERTICAL MILLING TABLEMounts to lathe or mill table to move work up and down. Has 2.25" of vertical travel and 8" long table. | 1.14kg 2.5lbs | £151.30 |
| 1187 | CHUCK-TO-T-SLOT ADAPTERAllows 3- or 4-jaw chuck to be quickly screwed to mill table. | 0.03kg 0.06lbs | £9.70 |
| 1191 | LIVE CENTERBall bearings allow center to rotate with part to reduce friction when turning between centers | 0.11kg 0.25lbs | £50.40 |
| 1201 | ADJUSTABLE LIVE CENTERBall bearing live center adjusts for perfect centering of headstock and tailstock | 0.23kg 0.5lbs | £81.90 |
| 1202 | ADJUST. TAILSTOCK CHUCK ARBORAllows perfect centering of tailstock chuck in relation to headstock | 0.23kg 0.5lbs | £56.90 |
| 1203 | ADJUST. TAILSTOCK TOOL HOLDERAllows perfect centering of round tools held in tailstock | 0.23kg 0.5lbs | £56.90 |
| 1206 | ADJUST. TAILSTOCK 1″ DIE HOLDER w/ 13/16″ bushingAllows perfect centering of 1" or 13/16" threading dies | 0.23kg 0.5lbs | £75.70 |
| 1220 | TAILSTOCK SPINDLE EXTENDERDesigned for lathes built before July, 1996 to extend reach of tailstock spindle over table. Not needed on newer lathes | 0.23kg 0.5lbs | £50.40 |
| 1230 | #0 MORSE ARBOR TO 3/4-16 CHUCK THREAD ADAPTERAllows a 3- or 4-jaw chuck to be mounted on the tailstock spindle | 0.23kg 0.5lbs | £50.40 |
| 1270 | COMPOUND SLIDERedesigned, Replaces P/N 1080. An alternate and more traditional way of turning tapers | 0.45kg 1lbs | £157.50 |
| 1272 | COMPOUND SLIDE RISER BLOCKRaises compound slide about 1" for use on front side of crosslide with riser blocks in place on lathe | 0.23kg 0.5lbs | £44.10 |
| 1288 | RISER ROCKER TOOL POSTTaller tool post for use with riser blocks in place on the lathe | 0.23kg 0.5lbs | £50.40 |
| 1289 | RISER 3/8″ INSERT TOOL POSTTaller tool post for holding 3/8" shank tools with riser blocks in place on the lathe. | 0.23kg 0.5lbs | £50.40 |
| 1290 | STEADY REST RISERLifts steady rest to match headstock when spacer block is in place. Used mainly by those who leave spacer blocks in place at all times on their lathe. | 0.11kg 0.25lbs | £63.20 |
| 1291 | SPACER BLOCK KITLifts headstock 1.25" to allow parts up to 6" diameter to be turned. Includes extended riser rocker tool post | 0.68kg 1.5lbs | £88.20 |
| 1292 | TAILSTOCK RISER BLOCKLifts tailstock 1.25" for turning between centers with headstock riser block in place | 0.45kg 1lbs | £63.20 |
| 1296 | CUTOFF TOOL HOLDER RISER BLOCKLifts cutoff tool P/N 3002 for use with riser blocks in place. Used with tool upside down on back side of crosslide table. | 0.23kg 0.5lbs | £63.20 |
| 1297 | MILL HEADSTOCK SPACER BLOCKSame as riser block for lathe, but without tool post. Adds 1.25" of throat distance when milling | 0.34kg 0.75lbs | £56.60 |
| 1300 | MILL COLUMN SPACER BLOCKRaises column base 2" for greater Z-axis clearance. Includes longer bolts for mounting. | 0.68kg 1.5lbs | £50.40 |
| 2045 | HEX AND OCTAGON INDEX BLOCK SETFits in mill vise to allow simple indexing of 2, 3, 4, 6 or 8 sides or hole patterns | 0.91kg 2lbs | £75.70 |
| 2049 | SPINDLE HANDWHEELUsed to rotate the headstock spindle much like the large handwheel on a sewing machine is used | 0.68kg 1.5lbs | £56.60 |
| 2083 | WW COLLET 1″ BLANKMake your own custom tool holder or collet that is held with the WW adapter and drawbar | 0.03kg 0.06lbs | £37.90 |
| 2085 | WW COLLET TAILSTOCK ADAPTERUse with P/N 1203) (Allows WW collets to be held in the tailstock | 0.11kg 0.25lbs | £69.10 |
| 2086 | 8mm COLLET TAILSTOCK ADAPTERUse with P/N 1203 | 0.11kg 0.25lbs | £75.70 |
| 2090 | 8.0mm COLLET TO 3/4-16 THREADFor mounting Sherline chuck on watchmaker's or jeweler's lathe that takes 8.0mm collets | 0.23kg 0.5lbs | £50.40 |
| 2091 | 10mm “D” COLLET TO 3/4-16 THREADFor mounting Sherline chuck on watchmaker's or jeweler's lathe that takes 10mm D collets, not for use on Sherline lathe. | 0.23kg 0.5lbs | £56.60 |
| 2092 | 8.0mm COLLET TO 3/8-24 THREADFor mounting chuck with 3/8-24 thread on watchmaker's or jeweler's lathe that takes 8.0mm collets, not for use on Sherline lathe. | 0.23kg 0.5lbs | £50.40 |
| 2093 | 10.0mm COLLET TO 3/8-24 THREADFor mounting chuck with 3/8-24 thread on watchmaker's or jeweler's lathe that takes 10mm D collets, not for use on Sherline lathe. | 0.23kg 0.5lbs | £56.60 |
| 2094 | CLOCKMAKER’S GEAR CUTTING ARBOR, 7.0mm to Morse #1Arbor for use on watchmaker or jeweler's lathes to hold round gear cutter, Not for use on Sherline lathe | 0.23kg 0.5lbs | £75.70 |
| 2095 | CLOCKMAKER’S GEAR CUTTING ARBOR, 7.0mm to 10mm “D” ColletArbor for use on watchmaker's or jeweler's lathes to hold round gear cutter. not for use on Sherline lathe | 0.23kg 0.5lbs | £75.70 |
| 2096 | CLOCKMAKER’S GEAR CUTTING ARBOR, 7.0mm to 8.0 mm WW ColletArbor for use on watchmaker's or jeweler's lathes to hold round gear cutter, not for use on Sherline lathe | 0.23kg 0.5lbs | £75.70 |
| 2100 | WW 3/4″ COLLET POT CHUCKCollet pot chucks are like small chucks custom turned to hold a particular part. The part is held in a depression turned in the surface of the pot chuck and does not go all the way through. Includes dowel pin to clamp on while turning to size. | 0.03kg 0.06lbs | £31.60 |
| 2101 | WW 1″ COLLET POT CHUCKSee 2100 | 0.03kg 0.06lbs | £34.10 |
| 2102 | WW 1-1/4″ COLLET POT CHUCKSee 2100 | 0.03kg 0.06lbs | £37.90 |
| 2103 | 10mm 3/4″ COLLET POT CHUCKNot for use on Sherline lathe | 0.05kg 0.12lbs | £44.10 |
| 2104 | 10mm 1″ COLLET POT CHUCKNot for use on Sherline lathe | 0.05kg 0.12lbs | £50.40 |
| 2105 | 10mm 1-1/4″ COLLET POT CHUCKNot for use on Sherline lathe | 0.05kg 0.12lbs | £56.60 |
| 2106 | LIVE CENTER-TO-8mm COLLETA live center for watchmaker's or jeweler's lathes. | 0.11kg 0.25lbs | £94.40 |
| 2107 | LIVE CENTER-TO-10mm COLLETA live center for watchmaker's or jeweler's lathes. | 0.11kg 0.25lbs | £94.40 |
| 2110 | W.R. SMITH WATCHMAKER’S T-RESTUsed on Sherline lathes to support a hand-held "graver", a traditional watchmaker's tool. Turns Sherline lathe into a first class watch or clock maker's lathe. Designed by famed craftsman W.R. Smith. Graver-making instructions included. | 0.45kg 1lbs | £251.90 |
| 2200 | RADIUS CUTTING ATTACHMENTFor cutting ball ends, convex and concave radii on ends of parts and even complete balls | 0.45kg 1lbs | £151.30 |
| 2250 | QUICK CHANGE TOOL POST w/ 3 holdersSaves time when changing tools. Holders included for 1/4" cutter, round boring tool and cutoff tool. Cutting tools not included. | 1.36kg 3lbs | £327.50 |
| 2251 | QUICK CHANGE TOOL POST RISERBrings quick-change tool post up to proper centerline height when using a riser block under the headstock for cutting larger diameters. | 0.8kg 1.75lbs | £63.20 |
| 2256 | RIGHT-HAND 35° CARBIDE INSERT TOOL HOLDER (Includes one 55° insert)Use in 7600 tool post. Carbide is used to cut hard-to-machine materials like stainless steel | 0.11kg 0.25lbs | £56.60 |
| 2257 | LEFT-HAND 35° CARBIDE INSERT TOOL HOLDERIncludes one 55° insert) (Use in 7600 tool post. Carbide is used to cut hard-to-machine materials like stainless steel | 0.11kg 0.25lbs | £56.60 |
| 2258 | PAIR OF RIGHT- and LEFT-HAND 35° INSERT TOOL HOLDERSIncludes one 55° insert per holder) (Replacement inserts, P/N 7605) (Save £19.50 by buying both LH and RH tools together | 0.23kg 0.5lbs | £88.20 |
| 2259 | 80° INSERT 3/8″ ROUND BORING TOOL, 1/2″ min. hole, carbide insert includedUse w/ P/N 7600 tool post | 0.07kg 0.15lbs | £75.70 |
| 2260 | 55° INSERT 3/8″ ROUND BORING TOOL, 3/4″ min. hole, carbide insert includedUse w/ P/N 7600 tool post | 0.07kg 0.15lbs | £75.70 |
| 2261 | PAIR OF 80° (P/N 2259) AND 55° (P/N 2260) 3/8″ ROUND BORING TOOLS w/ inserts | 0.11kg 0.25lbs | £119.70 |
| 2280 | 1/4″ QUICK-CHANGE TOOL BIT HOLDER (Incl. w/ 2250) | 0.45kg 1lbs | £75.70 |
| 2285 | 3/8″ QUICK-CHANGE BORING TOOL HOLDER (Incl. w/ 2250) | 0.45kg 1lbs | £75.70 |
| 2290 | QUICK-CHANGE CUTOFF TOOL HOLDER (Incl. w/ 2250) | 0.45kg 1lbs | £100.70 |
| 2295 | CARBIDE INSERT HOLDER for QUICK-CHANGE TOOL POST | 0.45kg 1lbs | £113.50 |
| 3001 | POWER FEED (120V.) (for 240V. see P/N 3011)Single direction motor drives lathe leadscrew .9" per minute to provide smooth final cut on long parts. Not designed for use with thread cutting attachment. | 2.27kg 5lbs | £113.50 |
| 3002 | CUTOFF TOOL & HOLDERFor cutting off work piece from the raw stock from which it was turned. Often called a "parting tool". | 0.11kg 0.25lbs | £63.20 |
| 3003 | TWO-POSITION TOOL POSTHolds two 1/4" cutting tools for quicker tool changes | 0.11kg 0.25lbs | £20.40 |
| 3004 | KNURLING TOOL HOLDERMakes knurled finishes. Includes one set of spiral knurls. Other sizes and patterns available | 0.11kg 0.25lbs | £94.40 |
| 3005 | 1/4″ SQ. HIGH SPEED STEEL TOOL BLANKSharpen yourself on a bench grinder for standard or custom-shaped tools | 0.03kg 0.06lbs | £4.10 |
| 3006 | CARBIDE TOOL SET (3 PC) (LH, RH, 60° THREADING)Carbide tips are brazed to 1/4" tool shanks. For cutting hard materials | 0.17kg 0.38lbs | £25.40 |
| 3007 | HIGH SPEED STEEL TOOL SET (3 PC) (LH, RH, BORING)Pre-sharpened to save you time. For cutting most materials | 0.05kg 0.12lbs | £31.60 |
| 3008 | TWO-POSITION TOOL POST, 5/16″ – 3/8″Holds 5/16" tool on one side, 3/8" on other side. Allows use of tools other than 1/4" | 0.11kg 0.25lbs | £31.60 |
| 3009 | CUTTING TOOL HEIGHT GAUGEUsed to assure tool tip on resharpened tools is set to proper centerline height. Works with both regular or riser toolpost | 0.11kg 0.25lbs | £25.40 |
| 3011 | POWER FEED (240V)See P/N 3001 | 2.27kg 5lbs | £128.50 |
| 3012 | HOLD-DOWN SETSimple strap clamp set for clamping parts to table for milling. Includes 2 clamps, T-nuts and assorted length bolts | 0.17kg 0.38lbs | £31.60 |
| 3013 | STEP BLOCK HOLD-DOWN SETThis is a smaller version of the sets used on most full-size mills. Quicker to use than 3012 and holds larger parts. Stepped blocks interlock to adjust height quickly. Spare block included to be cut to custom sizes | 0.45kg 1lbs | £50.40 |
| 3015 | TOGGLE SWITCH DUST SEALUse to keep fine dust out of speed contorl on/off switch when cutting brass or wood | 0.03kg 0.06lbs | £11.00 |
| 3016 | CUTOFF TOOL REAR MOUNTING BLOCKAllows 3002 cutoff tool to be mounted on "back" side of crosslide where it is out of the way and can be left in place for easy parting off. Cutoff blade mounts upside down for use in this position | 0.05kg 0.12lbs | £19.10 |
| 3017 | CROSSLIDE ACCESSORY PLATEStrengthens and protects lathe table when used for milling with vertical milling column. Not for use during lathe operations as tool post height will be incorrect. | 0.45kg 1lbs | £50.40 |
| 3018 | REAR MOUNT CUTOFF TOOL AND HOLDER | 0.11kg 0.25lbs | £63.20 |
| 3020 | SHERLINE “T” DRIVER5/32" hex driver with T-handle adjusts majority of 10-32 screws on Sherline tool. Easy to find on your bench. | 0.05kg 0.12lbs | £7.90 |
| 3021 | CENTER DRILL SET (3 PC., #1, #2, #3 double-ended)Center drills don't wander off center when starting holes. 60° tip makes proper hole to match dead or live center tips for turning between centers | 0.03kg 0.06lbs | £20.40 |
| 3035 | SPUR DRIVERA quick way to drive wood parts when turning between centers. | 0.11kg 0.25lbs | £31.60 |
| 3038 | WOOD TOOL REST (3″ & 5″ REST)Supports hand-held wood cutting tools for wood turning | 0.34kg 0.75lbs | £69.40 |
| 3047 | EXTENDED WOOD TOOL REST SET (For use w/ 1291)Like 3038 only with longer shafts to match height of headstock with riser block in place | 0.11kg 0.25lbs | £75.70 |
| 3050 | VERTICAL MILLING COLUMNConverts your lathe into a 3-axis mill in less than 30 seconds. | 3.64kg 8lbs | £189.10 |
| 3050-CNC | VERTICAL MILLING COLUMN, CNC READYConverts lathe into a 3-axis mill. Stepper motor mount is ready to accept NEMA 23 frame size stepper motor for CNC control | 4.09kg 9lbs | £316.30 |
| 3052 | FLY CUTTERFor quickly milling large, flat surfaces. | 0.23kg 0.5lbs | £44.10 |
| 3054 | BORING HEADFor enlarging holes to a precise inside diameter, uses 3/8" round boring tools | 0.23kg 0.5lbs | £88.20 |
| 3055 | MORSE #1 BLANKTurn on lathe and/or mill slots to make your own custom fly cutter, slitting saw holder or special tool holder | 0.23kg 0.5lbs | £20.40 |
| 3056 | T-NUTS, 10/32 (Set of 10) | 0.03kg 0.06lbs | £10.40 |
| 3057 | ROCKER TOOL POSTRocking insert with two screws allows adjustment of tool tip height for accurate turning. Eliminates shimming. Included on Model 4400/4410 lathes | 0.11kg 0.25lbs | £37.90 |
| 3058 | 4-JAW HOLD DOWN SETTwo angle clamps with T-nuts to clamp 4-jaw vise to any position on mill table. Included with 3551 mill vise | 0.05kg 0.12lbs | £7.90 |
| 3060 | MILLING COLLET SET (3 PC)(1/8", 3/16", 1/4") Milling collets have a #1 Morse taper and are pulled into the headstock with a drawbolt. They do not have a through hole like WW collets. They are used to hold specific size end mills or cutters. | 0.05kg 0.12lbs | £56.90 |
| 3061 | BORING TOOL—Max. Depth .600, Min. Hole 1/4″)Use w/ P/N 3054 boring head | 0.05kg 0.12lbs | £19.10 |
| 3063 | BORING TOOL—Max. Depth 1″, Min. Hole 5/16″Use with P/N 3054 boring head | 0.05kg 0.12lbs | £19.10 |
| 3064 | BORING TOOL—Max. Depth 1.5″, Min. Hole 5/16″Use w/ 3054 boring head | 0.05kg 0.12lbs | £22.90 |
| 3065 | SLITTING SAW HOLDERHolds small, round sawblades for cutting thin slots | 0.11kg 0.25lbs | £50.70 |
| 3070 | 2.5″ Dia. x 1-5/16″ STEEL BLANK (Chuck body) w/ 3/4-16 threadA billet of 12L14 steel threaded for the Sherline spindle, ready to turn it into whatever tool or part you need. A blank canvas for machinists. | 0.91kg 2lbs | £31.60 |
| 3074 | Tool holder for 1/4″ or 3/8″ Jacobs drill chucks3/4-16 female thread to 3/8-24 male thread adapter replaces #1 Morse arbor to allow drill chucks to be threaded on to outside thread of spindle to speed up tool changes on CNC machines. No variation in drill length when changing tools back and forth. Cannot be used with 5/32" Jacobs chucks as they do not have a threaded back. | 0.23kg 0.5lbs | £44.10 |
| 3075 | 5/16″ END MILL HOLDER | 0.23kg 0.5lbs | £37.90 |
| 3076 | 6.0mm END MILL HOLDER | 0.23kg 0.5lbs | £37.90 |
| 3077 | 8.0mm END MILL HOLDER | 0.23kg 0.5lbs | £37.90 |
| 3078 | 10.0MM END MILL HOLDERMost common size metric tool holder | 0.23kg 0.5lbs | £37.90 |
| 3079 | 3/8″ END MILL HOLDERMost common size inch tool holder. 3/8" end mills are available from many sources and are, therefore, the least expensive and available in the largest selection. | 0.23kg 0.5lbs | £37.90 |
| 3080 | END MILL SET (1/4″ SHK) (1/8″, 3/16″, 1/4″) | 0.03kg 0.06lbs | £37.90 |
| 3087 | 3/32″ MILL COLLET | 0.03kg 0.06lbs | £25.40 |
| 3089 | 5/32″ MILL COLLET | 0.03kg 0.06lbs | £25.40 |
| 3090 | 3-PC. METRIC MILL COLLET SET w/ 3.0, 4.0 and 6.0 mm colletsSee P/N 3060 for inch version set and description. | 0.07kg 0.15lbs | £56.90 |
| 3091 | 7/32″ MILL COLLET | 0.03kg 0.06lbs | £25.40 |
| 3092 | 3.0MM MILL COLLET | 0.03kg 0.06lbs | £20.70 |
| 3093 | 4.0MM MILL COLLET | 0.03kg 0.06lbs | £20.70 |
| 3094 | 6.0MM MILL COLLET | 0.03kg 0.06lbs | £20.70 |
| 3095 | 1/8″ MILL COLLET | 0.03kg 0.06lbs | £20.70 |
| 3096 | 3/16″ MILL COLLET | 0.03kg 0.06lbs | £20.70 |
| 3097 | 1/4″ MILL COLLET | 0.03kg 0.06lbs | £20.70 |
| 3098 | MILL COLLET (Special Order .125 to .312)Allow 3 weeks delivery | 0.03kg 0.06lbs | £63.20 |
| 3100 | THREAD-CUTTING ATTACHMENTBeing able to cut threads on your lathe frees you from the expense of purchasing a lot of expensive taps and dies for non-standard size threads. Cut just about any thread, inch or metric, using this set of change gears. Hand crank wheel included | 1.36kg 3lbs | £157.50 |
| 3200 | INDEXING ATTACHMENTIndexes in 5° increments, uses rack gear to turn rotation into measurable linear movement for divisions other than 5° multiples. Includes base and tailstock. | 3.64kg 8lbs | £251.90 |
| 3217 | GEAR TOOTH CUTTER HOLDER & HSS BLANKGrind gear shape into tool blank and use on mill in conjunction with indexing attachment or rotary table to cut your own gears. | 0.23kg 0.5lbs | £44.10 |
| 3230 | MILL ARBOR-7/8″ DIA. (Short)Holds round mill cutters | 0.23kg 0.5lbs | £63.20 |
| 3231 | MILL ARBOR-7/8″ DIA. (Long)Holds round mill cutters | 0.23kg 0.5lbs | £63.20 |
| 3235 | MILL ARBOR-1″ DIA. (Short)Holds round mill cutters | 0.23kg 0.5lbs | £63.20 |
| 3236 | MILL ARBOR-1″ DIA. (Long)Holds round mill cutters | 0.23kg 0.5lbs | £63.20 |
| 3306 | STD. HEADSTOCK, DC MOTOR AND SPEED CONTROLComplete, self-contained drive unit with pulleys designed to turn the spindle at speeds up to 2800 RPM. Alternate pulley position provides more torque and a maximum spindle speed of 1400 RPM. Operates on any current 100VAC to 240VAC, 50 or 60 Hz. | 4.55kg 10lbs | £403.20 |
| 3307 | 10,000 RPM HEADSTOCK, DC MOTOR AND SPEED CONTROLComplete, self-contained drive unit with pulleys designed to turn the spindle at speeds up to 10,000 RPM. Alternate pulley position provides more torque and a maximum spindle speed of 2200 RPM. Operates on any current 100VAC to 240VAC, 50 or 60 Hz. | 4.55kg 10lbs | £504.10 |
| 3400 | OVERSIZE HANDWHEEL2.5" diameter for easier cranking | 0.05kg 0.12lbs | £19.10 |
| 3420 | 2″ ADJUSTABLE ZERO HANDWHEELMill Y-axis or lathe crosslide | 0.11kg 0.25lbs | £44.10 |
| 3440 | 2.5″ ADJUSTABLE ZERO HANDWHEELMill Y-axis or lathe leadscrew | 0.11kg 0.25lbs | £50.70 |
| 3460 | 2.5″ ADJUSTABLE ZERO HANDWHEELW/Thrust & Bearing Set for Mill Z-axis | 0.11kg 0.25lbs | £56.90 |
| 3480 | VERTICAL MILLING COLUMN W/ADJ. HANDWHEELTurns lathe into a mill in less than 30 seconds. Normally used with 4500 or 4400 lathes to match adj. Zero handwheels. | 3.64kg 8lbs | £214.10 |
| 3500 | ROTARY COLUMN ATTACHMENTAllows mill column to be swung up to 90° to either side for angled drilling. | 0.8kg 1.75lbs | £101.30 |
| 3551 | MILLING VISEHolds work for milling. Looks similar to a drill press vise, but jaw pulls down and in to keep parts from lifting during milling. Precise jaws and body can be squared up with table. | 1.14kg 2.5lbs | £94.40 |
| 3559 | 90° ANGLE PLATEMounts parts 90° to table for milling | 1.82kg 4lbs | £126.30 |
| 3560 | MILL TOOLING PLATEProtects mill table, pre-drilled hole pattern makes it easy to clamp parts, mount mill vise or rotary table to mill. | 1.14kg 2.5lbs | £75.70 |
| 3570 | ROTATING MILL VISE BASEHolds mill vise while allowing it to be rotated 360° using laser engraved scale for angle reference | 0.45kg 1lbs | £126.30 |
| 3575 | ROTATING MILL VISE BASE AND MILL VISE (P/N 3551)Save by buying vise and base at same time | 1.14kg 2.5lbs | £208.20 |
| 3580 | MULTI-DIRECTION DELUXE VERTICAL MILLING COLUMNTurns your lathe into an 8-direction mill in 30 seconds | 5.91kg 13lbs | £472.50 |
| 3700 | 4″ PRECISION ROTARY TABLE72:1 worm gear divides a circle into 3600 parts without interpolation. Used for indexing radial hole patterns or milling radii or indexed flats. Used on 3701 or 3750 to index for cutting gear teeth. A mill with a rotary table is an extremely potent combination, make virtually any part possible, with size being the only limitation | 3.64kg 8lbs | £340.40 |
| 3700-CNC | 4″ PRECISION ROTARY TABLE, CNC-READYIncludes stepper motor mount ready for application of your own stepper motor and CNC controls. Handwheel also included | 5kg 11lbs | £403.20 |
| 3701 | RIGHT ANGLE ATTACHMENT (For use with P/N 3700)Mounts rotary table perpendicular to mill table | 1.36kg 3lbs | £94.40 |
| 3702 | RIGHT ANGLE ADJUSTABLE TAILSTOCKFor use with P/N 3700. Aligns with center of rotary table when mounted on 3701. Supports arbor shaft used to hold gear blanks when cutting teeth. | 0.91kg 2lbs | £94.40 |
| 37091 | 12 mm to 3/8-16 ADAPTERAllows Chuck with 12 mm thread to be mounted to Sherline rotary table P/N 3700 | 0.11kg 0.25lbs | £23.50 |
| 37092 | 14 mm to 3/8-16 ADAPTERAllows Chuck with 14mm thread to be mounted to Sherline rotary table P/N 3700 | 0.11kg 0.25lbs | £11.00 |
| 3750 | TILTING ANGLE TABLEMount part, mill vise, chucks or rotary table to mill any angle from 0° to 90°. In 90° position, holds rotary table at same height as 3701, eliminating the need for that part | 1.14kg 2.5lbs | £138.80 |
| 4017U | MILL SADDLE LOCKING LEVER UPGRADEAllows Z-axis leadscrew to be locked with a lever on the leadscrew instead of tightening a screw with a hex wrench. Standard on all mills after 1998 | 0.23kg 0.5lbs | £31.60 |
| 4017Z | CNC MILL ANTIBACKLASH ADJUSTER UPGRADEAllows the Z-axis locking lever to be positioned in partially locked positions to reduce backlash to as little as .001". Standard on CNC mills after 2/04. Can be installed as an option on any Sherline mill. | 0.23kg 0.5lbs | £44.10 |
| 4150 | 15″ LATHE VINYL COVERProtect your 4000-series lathe from dust and grit | 0.11kg 0.25lbs | £15.40 |
| 4151 | 24″ LATHE VINYL DUST COVERProtect your 4400-series lathe from dust and grit | 0.11kg 0.25lbs | £17.90 |
| 4335 | 10,000 RPM PULLEY CONVERSIONHigh speed position allows motor to turn spindle at a maximum of 10,000 RPM. Second belt position provides more torque and a maximum of 2200 RPM. New 2-piece standoff replaces standard motor standoffs. Installs in about 10 minutes. | 0.45kg 1lbs | £101.00 |
| 4360 | CHIP GUARDClear shield contains flying chips. Pivots out of the way when not needed. Not a substitute for safety glasses | 0.23kg 0.5lbs | £19.10 |
| 4417Z | CNC LATHE BACKLASH ADJUSTERInstalls on leadscrew to provide a way to reduce backlash during CNC operations. Similar to the 4017Z lock developed for the mill, it uses a lever which is tightened against the saddle nut to control backlash. A positioning arm holds the locking lever in any desired position. Installed on all CNC-ready lathes as of 5/04. Can be installed as an option on any Sherline lathe. | 0.23kg 0.5lbs | £47.20 |
| 5011U | MILL X and Y AXIS STAR GEAR BACKLASH UPGRADEInstalls on mills made after 1997 when the pointer style backlash lock was replaced with the star gear type lock and up until July, 2004 when this change was incorporated into regular production. Includes new star gears and leadscrew nuts with finer teeth for mill X and Y axis plus new button head screws to hold the locking gear. | 0.05kg 0.1lbs | £12.20 |
| 5150 | MILL VINYL COVERProtects your 2000-series mill from dust and grit | 0.11kg 0.25lbs | £17.90 |
| 5151 | MILL VINYL COVERProtects your 2000-series mill from dust and grit | 0.11kg 0.25lbs | £20.70 |
| 5200 | XY BASE (10″) (Inch)Add a 3050 vertical milling column and the motor/speed control from your lathe and you have a model 5000 mill | 7.73kg 17lbs | £327.50 |
| 5200-CNC | XY BASE (10″) CNC READY (Inch) w/ 2 stepper motor mountsStepper motors and CNC controls not included. | 9.09kg 20lbs | £548.20 |
| 5201 | XYZ BASE (10″) (Inch)Add the motor/speed control from your lathe and you have a model 5000 mill | 11.82kg 26lbs | £579.70 |
| 5201-CNC | XYZ BASE (10″) CNC READY (Inch) w/ 3 stepper motor mountsStepper motors and CNC controls not included. | 12.27kg 27lbs | £894.70 |
| 5220 | XY BASE (10″) W/ ADJUST. HANDWHEELSAdd a vertical milling column with adjustable handwheels and the motor/speed control from your lathe and you have a complete model 5500/5510 mill | 8.64kg 19lbs | £422.20 |
| 5230 | XYZ BASE (10″ W/ ADJUST. HANDWHEELSAdd the motor/speed control from your lathe and you have a complete model 5500/5510 mill | 11.82kg 26lbs | £649.10 |
| 5300 | HOME MACHINIST’S HANDBOOK by Doug Briney275 pages, B/W, uses Sherline tools in all the setup examples, project plans included | 0.91kg 2lbs | £26.30 |
| 5301 | TABLETOP MACHINING by Joe MartinThe ultimate miniature machining book by Sherline's owner. All color, 8-1/2 x 11, 400+ photos, 200+ illustrations. Third printing, 11/01 includes 8 more pages and several new photos. | 1.36kg 3lbs | £50.70 |
| 5325 | SHERLINE TOOLS & ACCESSORIES CATALOG, 6th Edition48-page color catalog shows tools and accessories plus tells briefly how each is used. Current price lists enclosed. | 0.23kg 0.5lbs | £3.80 |
| 5326 | SHERLINE ASSEMBLY AND INSTRUCTION GUIDE, 4th Edition44-page color instruction book included with new machines. A good basic course in machining | 0.23kg 0.5lbs | £3.80 |
| 5327 | SHERLINE SHOP GUIDE144 pages, B/W, 8.5 x 11" perfect bound book incorporates illustrated instructions from all of Sherline's major accessories into one volume. | 1.36kg 3lbs | £12.50 |
| 5328 | STEAM ENGINE VIDEO by Rudy KouhouptVHS, 3 Hrs., includes materials list and printed plans for a steam engine. Video takes you through every setup from start to finish. | 0.91kg 2lbs | £88.20 |
| 5329 | SHOP SECRETS—USING MEASURING TOOLS by Mike RehmusVHS, 2 hrs., tells you how each measuring tool used in machining is used and cared for. Very professionally produced. Includes promo for NAMES show too | 0.45kg 1lbs | £50.70 |
| 5330 | SAFETY GLASSESA MUST in every shop. Get them from us or get them from someone else, but don't cut metal without them! These are good quality and comfortable. | 0.11kg 0.25lbs | £9.70 |
| 5401 | DELUXE XY BASE (Inch) w/ 12″ Base and Adjustable HandwheelsAdd a 3480 vertical milling column and the motor/speed control from your lathe and you have a complete deluxe model 5400 mill. | 8.64kg 19lbs | £510.40 |
| 5401-CNC | DELUXE XY BASE CNC READY w/ 2 stepper motor mountsStepper motors and CNC controls not included. | 9.55kg 21lbs | £649.10 |
| 5420 | DELUXE XYZ BASE (Inch) w/ 12″ Base and Adjustable HandwheelsAdd the motor/speed control from your lathe and you have a complete deluxe model 5400 mill. | 12.27kg 27lbs | £688.20 |
| 5420-CNC | DELUXE XYZ BASE CNC READY (Inch) w/ 3 stepper motor mountsStepper motors and CNC controls not included. | 12.73kg 28lbs | £945.00 |
| 5600 | Model 2000 8-DIRECTION MILL XY BASEAdd a multi-direction vertical milling column and the motor/speed control from your lathe and you have a complete model 2000 mill. | 10kg 22lbs | £535.70 |
| 5625 | Model 2000 8-DIRECTION MILL XYZ BASEAdd the motor/speed control from your lathe and you have a complete model 2000 mill. | 15.45kg 34lbs | £945.00 |
| 5650 | 8-DIRECTION UPGRADE for all existing SHERLINE MILLSA multi-direction milling column and an offset base brings your existing mill up to the capabilities of a model 2000 mill. | 4.09kg 9lbs | £334.10 |
| 5680 | 8-DIRECTION UPGRADE for LATHE VERTICAL MILLING COLUMNTurns your lathe/vertical milling column combination into an 8-direction mill. | 4.09kg 9lbs | £334.10 |
| 6079 | 1/4″ END MILL HOLDERHolds end mills in 3080 set | 0.23kg 0.5lbs | £37.90 |
| 6080 | 3/16″ END MILL HOLDER | 0.23kg 0.5lbs | £37.90 |
| 6081 | 1/8″ END MILL HOLDER | 0.23kg 0.5lbs | £37.90 |
| 6100 | HORIZONTAL MILLING CONVERSION | 5kg 11lbs | £163.80 |
| 6101 | COLUMN CONVERSIONTo optimize the horizontal conversion, P/N 6100, the mill column should be reworked to allow for the best set up. Contact SHERLINE for information. | 3.64kg 8lbs | not known |
| 6700 | CNC UPGRADE KIT, 5000 OR 5400 MILLReplaces the handwheels with stepper motor mounts, ready for the installation of your own stepper motors and CNC control. | 1.14kg 2.5lbs | £315.00 |
| 6705 | CNC UPGRADE KIT, 2000 MILLReplaces the handwheels with stepper motor mounts, ready for the installation of your own stepper motors and CNC control. | 1.14kg 2.5lbs | £337.50 |
| 67127 | STEPPER MOTOR2 amp, #23 Frame, dual shaft, 6-wire, 136 oz-in stall torque, pre-wired with plug for use with Sherline rotary or linear controller, flats pre-machined for Sherline coupler and handwheel set screws. | 0.45kg 1lbs | £94.40 |
| 67130 | STEPPER MOTOR2 amp, #23 Frame, dual shaft, 6-wire, 136 oz-in stall torque, 6-wire plug-in harness with raw leads for use on applications that do not have the Sherline 5-pin connector plug, flats pre-machined for Sherline coupler and handwheel set screws. | 0.45kg 1lbs | £81.90 |
| 6720 | CNC UPGRADE KIT, 4000 or 4500 LATHEReplaces the handwheels with stepper motor mounts, ready for the installation of your own stepper motors and CNC control. | 0.91kg 2lbs | £269.10 |
| 6730 | CNC UPGRADE KIT, 4400 LATHEReplaces the handwheels with stepper motor mounts, ready for the installation of your own stepper motors and CNC control. | 0.91kg 2lbs | £282.50 |
| 6740 | CNC UPGRADE KIT, 5000 and 5400 Series Mills, Z-axis only | 0.68kg 1.5lbs | £132.50 |
| 6750 | CNC UPGRADE KIT, 2000 Series Mills, Z-axis only | 0.68kg 1.5lbs | £132.50 |
| 6760 | CNC UPGRADE KIT, mill X axis or lathe Crosslide only (all models) | 0.45kg 1lbs | £94.40 |
| 6770 | CNC UPGRADE KIT, mill Y axis only (all mill models) | 0.45kg 1lbs | £94.40 |
| 6780 | CNC UPGRADE KIT, leadscrew axis only, 4000/4500-series lathes | 0.45kg 1lbs | £175.00 |
| 6790 | CNC UPGRADE KIT, leadscrew axis only, 4400-series lathes | 0.45kg 1lbs | £188.50 |
| 7506 | SET OF MACHINIST’S PARALLELSSets of two parallel bars in five different sizes sized for miniature machine tools. Used to support work a known distance above and parallel to the table. | 0.11kg 0.25lbs | £63.20 |
| 7550 | Super-Lube multi-purpose synthetic grease with Syncolon® (PTFE), 3 oz tubeTeflon-based grease that we use at the factory on all new machines. Clear, non-staining, heat resistant. | 0.11kg 0.25lbs | £10.40 |
| 7555 | Super-Lube dri-film spray lubricant with Syncolon® (PTFE), 11 oz aerosol canTeflon-based film that sprays on. Once propellant dries, it leaves a thin coat of dry lubricant that won't attract chips. | 0.45kg 1lbs | £18.80 |
| 7600 | 3/8″ INSERT HOLDER TOOL POSTHas side slot to hold 3/8" shank cutting tool holders plus a 3/8" round hole to hold round boring bars. | 0.11kg 0.25lbs | £25.40 |
| 7610 | 55° NEGATIVE RAKE INSERT HOLDER w/ insertHolds carbide tips for cutting hard materials like stainless steel. 5° angle provides negative clearance for the cutter, which is supported all the way down to the table for rigidity. | 0.23kg 0.5lbs | £75.70 |
| 7612 | REPLACEMENT 4-SIDED CARBIDE INSERT TOOL (for 7610) | 0.03kg 0.06lbs | £20.00 |
| 7620 | SINGLE FLUTE INSERT FLY CUTTERCarbide insert cuts hard materials. Also is a good compromise between a fly cutter and an end mill, because it will cut a 1-1/8" wide path while still being able to cut right up to a shoulder. | 0.23kg 0.5lbs | £75.70 |
| 7622 | REPLACEMENT 2-SIDED CARBIDE TIP (for 7620) | 0.03kg 0.06lbs | £20.00 |
| 8100 | 3-AXIS DIGITAL READOUT w/ RPM GAGE FOR MILL (inch)Reads table position to .0005", electronic compensation for backlash | 1.36kg 3lbs | £472.50 |
| 8200 | 2-AXIS DIGITAL READOUT w/ RPM GAGE FOR LATHE (inch)Reads table position to .0005", electronic compensation for backlash | 1.36kg 3lbs | £409.40 |
| 8210 | 3-AXIS DIGITAL READOUT w/ RPM GAGE FOR LATHE and VERTICAL MILLING COLUMN (Inch)Reads table position to .0005", electronic compensation for backlash | 1.36kg 3lbs | £485.00 |
| 8220 | 2-AXIS DIGITAL READOUT w/ RPM GAGE FOR LATHE without READOUT BOXFor those who already have a Mill DRO package. (Inch) Reads table position to .0005", electronic compensation for backlash. | 0.91kg 2lbs | £207.90 |
| 8240 | Z-AXIS VERTICAL MILLING COLUMN DIGITAL READOUT HANDWHEEL PACKAGE (Inch)Adds third readout for those who bought 2-axis DRO and later add a vertical milling column. | 0.23kg 0.5lbs | £91.00 |
| 8700 | CNC ROTARY INDEXER w/ CONTROLLERCNC ROTARY INDEXER w/ CONTROLLER, STEPPER MOTOR, MOUNT, POWER SUPPLY, CABLES, 4″ ROTARY TABLE AND HOLD-DOWNS (Inch) | 7.73kg 17lbs | £913.80 |
| 8710 | CNC ROTARY TABLE RISER PLATEOn the 3700-CNC and 8700 CNC rotary tables, the bottom of the stepper motor mount extends slightly below the bottom surface of the table. On Sherline mills, the mount overhangs the side of the table so this is not a problem. On larger mills or flat table applications a riser plate is needed so that the stepper motor clears the table surface. | 0.91kg 2lbs | £37.90 |
| 8730 | CNC ROTARY TABLE WITH STEPPER MOTORStepper motor plugs into 4th axis cable of 8760 driver box or Sherline 8540 or 8020 CNC system to act as 4th axis. Includes prewired plug. | 4.55kg 10lbs | £497.90 |
| 8760 | CNC 4-AXIS DRIVER BOXIncludes 4 cables for X, Y, Z and A (Rotary) axes, power supply and parallel cable for attachment to computer's printer port. Linux OS and EMC 4-axis softare also included on two CD's. Buy or upgrade a CNC-ready Sherline machine, buy the needed P/N 67127 stepper motors, plug in and attach to your computer with Linux/EMC installed and you have the duplicate of a complete Sherline CNC system. NOTE: one hour of free technical support provided with Sherline CNC system is NOT provided when driver box is purchased separately. | 3.18kg 7lbs | £807.20 |
| 8765 | Upgrade any CNC-ready Sherline lathe to CNC (Computer not included.)Save compared to complete systems with computer. Includes 2 stepper motors, 4-axis 8760 driver box and Linux/EMC software on CD. Does NOT include software installation and technical support. | 4.09kg 9lbs | £982.20 |
| 8770 | Upgrade any CNC-ready Sherline lathe to CNC (Computer not included.)Save compared to complete systems with computer. Includes 2 stepper motors, 4-axis 8760 driver box and Linux/EMC software on CD. Does NOT include software installation and technical support. | 4.55kg 10lbs | £1083.20 |
| 8800 | CNC LINEAR CONTROLLER w/ STEPPER MOTOR (Inch)Stepper motor bolts onto Sherline CNC-ready stepper motor mounts. Controller drives stepper motor to move any axis on lathe or mill. From .0005" to 9.9995". Will work on any lathe or mill axis that already has a stepper motor mount installed. Includes power supply and cable. Can be daisy chained with other Sherline linear or rotary controllers. | 2.27kg 5lbs | £605.40 |
| 8850 | CNC MILL OR LATHE POWER FEEDReplaces handwheel on X- or Y-axis of mill or lathe crosslide with stepper motor mount and stepper motor. Motor is driven by self-contained computer/keypad unit and power supply to allow movement from .0005" to 9.9995". Includes drill block for locating mounting holes. Can be daisy chained with other Sherline controllers | 2.73kg 6lbs | £656.30 |
| 8860 | CNC MILL POWER FEEDReplaces handwheel on Z-axis of mill with stepper motor mount and stepper motor. Motor is driven by self-contained computer/keypad unit and power supply to move Z-axis in programmable .0005" increments up to full length of travel. Includes drill block for locating mounting holes. Can be daisy chained with other Sherline linear or rotary controllers. | 3.18kg 7lbs | £642.50 |
| 8865 | CNC MILL POWER FEEDSee description for 8860. | 3.18kg 7lbs | £642.50 |
| 8870 | CNC LATHE LEADSCREW POWER FEEDReplaces handwheel on long leadscrew of lathe with stepper motor mount and stepper motor. Motor is driven by self-contained computer/keypad unit and power supply to move the saddle from .0005 to 9.9995". Includes drill block for locating mounting holes. Can be daisy chained with other Sherline linear or rotary controllers. | 3.18kg 7lbs | £699.40 |
| 8880 | CNC LATHE LEADSCREW POWER FEEDSee description for 8870 above. | 3.18kg 7lbs | £713.20 |
SHERLINE CHUCKS
| Part Number | Part | Weight | Cost |
|---|---|---|---|
| 1010 | 0JT 5/32″ Jacobs drill chuck w/ #1 Morse arbor (headstock), drawbolt and key | 0.23kg 0.5lbs | £88.20 |
| 1012 | Sensitive drilling attachmentSee Accessories section following chuck section. | 0.91kg 2lbs | £138.80 |
| 1015 | 0JT 5/32″ Jacobs drill chuck w/ #0 Morse (tailstock) arbor and keySherline Lathe | 0.23kg 0.5lbs | £88.20 |
| 1030 | 4-Jaw Chuck (3.125″ O.D.) | 0.91kg 2lbs | £170.00 |
| 1031 | 14 x 1 mm 3-jaw chuck (2.5″ O.D.)14 x 1 mm threads for use on Unimat 3 lathes. | 0.91kg 2lbs | £158.90 |
| 1035 | 14 x 1 mm 4-jaw chuck (2.5″ O.D.)14 x 1 mm threads for use on old Sears 6″ lathe | 0.91kg 2lbs | £151.30 |
| 1040 | 3-Jaw Chuck (3.125″ O.D.) | 0.91kg 2lbs | £176.30 |
| 1041 | 3-Jaw Chuck (2.5″ O.D.) | 0.91kg 2lbs | £126.30 |
| 1044 | 4-Jaw Chuck (2.5″ O.D.) | 0.91kg 2lbs | £138.50 |
| 1068 | 12 x 1 mm 3-jaw chuck (2.5″ O.D.) w/ reversible jaws12 x1 mm threads for use on Unimat SL 1000 | 0.91kg 2lbs | £151.30 |
| 1069 | 3/8″ Jacobs Tailstock Drill Chuck w/ #0 and #1 Morse arbors, drawbolt and key | 0.68kg 1.5lbs | £81.90 |
| 1070 | 1/2-20 3-Jaw (2.5″ O.D.)1/2-20 threads for use on Unimat 3 or Cowells lathes | 0.91kg 2lbs | £151.30 |
| 1071 | 12 x 1 mm 4-jaw chuck (2.5″ O.D.)12 x1 mm threads for use on Unimat SL 1000 | 0.91kg 2lbs | £151.30 |
| 1072 | 1/4″ Jacobs tailstock drill chuck w/ #0 and #1 Morse arbors, drawbolt and key | 0.23kg 0.5lbs | £69.40 |
| 1073 | 1/2-20 4-Jaw Chuck (2.5″ O.D.)1/2-20 threads for use on Unimat 3 or Cowells lathes | 0.91kg 2lbs | £151.30 |
| 1075 | Self-centering 4-Jaw Chuck (2.5″ O.D.) | 0.91kg 2lbs | £163.80 |
| 1076 | Self-centering 4-Jaw Chuck (3.125″ O.D.) | 0.91kg 2lbs | £207.90 |
| 3072 | 1/4″ Jacobs Drill Chuck w/ #1 Morse arbor, drawbolt and key#0 Morse arbor not incl. See P/N 1072 if you need both arbors | 0.23kg 0.5lbs | £63.20 |
| 3073 | 3/8″ Jacobs Drill Chuck w/ #1 Morse arbor, drawbolt and key#0 Morse arbor not incl. See P/N 1069 if you need both arbors | 0.34kg 0.75lbs | £75.70 |